Line 6: |
Line 6: |
| | part = Predicting the occurrence of oil and gas traps | | | part = Predicting the occurrence of oil and gas traps |
| | chapter = Applying gravity in petroleum exploration | | | chapter = Applying gravity in petroleum exploration |
− | | frompg = 15-1 | + | | frompg = 15-8 |
− | | topg = 15-28 | + | | topg = 15-9 |
| | author = David A. Chapin, Mark E. Ander | | | author = David A. Chapin, Mark E. Ander |
| | link = http://archives.datapages.com/data/specpubs/beaumont/ch15/ch15.htm | | | link = http://archives.datapages.com/data/specpubs/beaumont/ch15/ch15.htm |
Line 18: |
Line 18: |
| The table below outlines a suggested procedure for interpreting gravity. | | The table below outlines a suggested procedure for interpreting gravity. |
| | | |
− | {| class = "wikitable"
| + | # Use well logs and [http://www.merriam-webster.com/dictionary/outcrop outcrop] data to make structural [[cross section]]s through critical areas containing gravity data to be interpreted. |
− | |-
| + | # Plot gravity profiles above structural cross sections and seismic sections. Add magnetic profiles if available. |
− | ! Step
| + | # From geology interpreted from data, build gravity model sections. Divide the section into intervals of approximately the same density. |
− | ! Action
| + | # Calculate a predicted gravity profile. Check the observed profile against the calculated profile. Where differences exist, adjust the gravity model and recalculate the gravity profile until a suitable match between observed and calculated is made. |
− | |-
| + | # Check the interpretation of the gravity map, i.e., location of faults, against the model profiles and all other available data. |
− | | 1
| |
− | | Use well logs and outcrop data to make structural cross sections through critical areas containing gravity data to be interpreted.
| |
− | |-
| |
− | | 2
| |
− | | Plot gravity profiles above structural cross sections and seismic sections. Add magnetic profiles if available.
| |
− | |-
| |
− | | 3
| |
− | | From geology interpreted from data, build gravity model sections. Divide the section into intervals of approximately the same density.
| |
− | |-
| |
− | | 4
| |
− | | Calculate a predicted gravity profile. Check the observed profile against the calculated profile. Where differences exist, adjust the gravity model and recalculate the gravity profile until a suitable match between observed and calculated is made.
| |
− | |-
| |
− | | 5
| |
− | | Check the interpretation of the gravity map, i.e., location of faults, against the model profiles and all other available data.
| |
− | |}
| |
| | | |
| ==Interpreting structure== | | ==Interpreting structure== |
− | In many places in the world, structural highs have higher density and are expressed in the data as gravity highs because dense basement rocks are closer to the surface. Therefore, a gravity map often is used directly as a pseudostructure map. However, there is not a one-to-one relationship between milligals and depth; therefore, the map must be viewed in a qualitative sense as a formline map. There are exceptions, as well, where structural highs are gravity lows because dense basement rocks are not closer to the surface. These structures may be of lower density than the surrounding rocks. | + | In many places in the world, structural highs have higher density and are expressed in the data as gravity highs because dense [[basement]] rocks are closer to the surface. Therefore, a gravity map often is used directly as a pseudostructure map. However, there is not a one-to-one relationship between milligals and depth; therefore, the map must be viewed in a qualitative sense as a formline map. There are exceptions, as well, where structural highs are gravity lows because dense basement rocks are not closer to the surface. These structures may be of lower density than the surrounding rocks. |
| | | |
| ==Rock densities== | | ==Rock densities== |
− | The range of densities for all rock types (igneous, metamorphic, and sedimentary) is typically 1.60–3.20 g/cm<sup>3</sup>. The density values of sedimentary rocks typically range from 1.80 to 2.80 g/cm<sup>3</sup>. Thus, small variations of density in sedimentary rocks may be invisible to the method. A5–10% error in estimating subsurface densities from gravity is quite common. This is in contrast to [[magnetics]], where typically there are orders of magnitude variations in susceptibilities. | + | The range of densities for all rock types ([[igneous]], metamorphic, and sedimentary) is typically 1.60–3.20 g/cm<sup>3</sup>. The density values of sedimentary rocks typically range from 1.80 to 2.80 g/cm<sup>3</sup>. Thus, small variations of density in sedimentary rocks may be invisible to the method. A5–10% error in estimating subsurface densities from gravity is quite common. This is in contrast to [[magnetics]], where typically there are orders of magnitude variations in susceptibilities. |
| | | |
| ==Horizontal layers== | | ==Horizontal layers== |
− | Horizontal layers have no anomalous gravity response. Thus, it is impossible to determine the subsurface density distribution if there are no lateral changes. Layer-cake geology yields no anomalous gravity signal. A bed is considered infinite and horizontal if it is about five times wider in all directions than it is thick, with no dip. | + | Horizontal layers have no anomalous gravity response. Thus, it is impossible to determine the subsurface density distribution if there are no [[lateral]] changes. Layer-cake geology yields no anomalous gravity signal. A bed is considered infinite and horizontal if it is about five times wider in all directions than it is thick, with no [[dip]]. |
| | | |
| ==Interpretation ranges== | | ==Interpretation ranges== |
Line 52: |
Line 37: |
| | | |
| ==Depth-to-basement determination== | | ==Depth-to-basement determination== |
− | Gravity is not as good at depth-to-basement or depth-to-density anomaly estimations as other geophysical methods. Though possible to do, it is often difficult to determine the appropriate depth to geologic source unless other constraints exist. | + | Gravity is not as good at depth-to-basement or depth-to-density anomaly estimations as other [[geophysical methods]]. Though possible to do, it is often difficult to determine the appropriate depth to geologic source unless other constraints exist. |
| | | |
| ==Positions of geologic bodies== | | ==Positions of geologic bodies== |
Line 58: |
Line 43: |
| | | |
| ==Interpreting fault location== | | ==Interpreting fault location== |
| + | |
| + | [[file:applying-gravity-in-petroleum-exploration_fig15-3.png|500px|thumb|{{figure number|1}}Bouguer gravity maps of Spouthern California showing the expression of faults.]] |
| + | |
| Faults usually can be identified through either steep gradients or truncation of trends. | | Faults usually can be identified through either steep gradients or truncation of trends. |
| | | |
− | The figure below contains two Bouguer gravity maps of Southern California, showing the expression of faults. In the left map, locations ''a'' and ''b'' show strong gradients, which indicate faults. A series of truncated trends (dashed) near location c also indicate faults. The right map shows the actual location of the major faults over the same gravity map.
| + | [[:file:applying-gravity-in-petroleum-exploration_fig15-3.png|Figure 1]] contains two Bouguer gravity maps of Southern California, showing the expression of faults. In the left map, locations ''a'' and ''b'' show strong gradients, which indicate faults. A series of truncated trends (dashed) near location c also indicate faults. [[:file:applying-gravity-in-petroleum-exploration_fig15-3.png|Figure 1B]] shows the actual location of the major faults over the same gravity map. |
| | | |
− | [[file:applying-gravity-in-petroleum-exploration_fig15-3.png|thumb|{{figure number|15-3}}]]
| + | ==See also== |
| | | |
− | ==See also==
| |
− | * [[Applying general gravity methods]]
| |
| * [[Gravity basics]] | | * [[Gravity basics]] |
| * [[Processing gravity data]] | | * [[Processing gravity data]] |
Line 78: |
Line 64: |
| [[Category:Predicting the occurrence of oil and gas traps]] | | [[Category:Predicting the occurrence of oil and gas traps]] |
| [[Category:Applying gravity in petroleum exploration]] | | [[Category:Applying gravity in petroleum exploration]] |
| + | [[Category:Treatise Handbook 3]] |