Changes

==Organic richness: total organic carbon assessment==

==Organic richness: total organic carbon assessment==

One of the first and basic screening analyses for any source rock is organic richness, as measured by total organic carbon (TOC). The TOC is a measure of organic carbon present in a sediment sample, but it is not a measure of its generation potential alone, as that requires an assessment of hydrogen content or organic maceral percentages from chemical or visual kerogen assessments. As TOC values vary throughout a source rock because of organofacies differences and thermal maturity, and even depending on sample type, there has been a lengthy debate on what actual TOC values are needed to have a commercial source rock. All organic matter preserved in sediments will decompose into petroleum with sufficient temperature exposure; for EampP companies, it is a matter of the producibility and commerciality of such generation. In addition, the expulsion and retention of generated petroleum must be considered. However, original quantity (TOC) as well as source rock quality (type) of the source rock must be considered in combination to assess its petroleum generation potential.

One of the first and basic screening analyses for any source rock is organic richness, as measured by total organic carbon (TOC). The TOC is a measure of organic carbon present in a sediment sample, but it is not a measure of its generation potential alone, as that requires an assessment of hydrogen content or organic maceral percentages from chemical or visual [[kerogen]] assessments. As TOC values vary throughout a source rock because of organofacies differences and thermal maturity, and even depending on sample type, there has been a lengthy debate on what actual TOC values are needed to have a commercial source rock. All organic matter preserved in sediments will decompose into petroleum with sufficient temperature exposure; for EampP companies, it is a matter of the producibility and commerciality of such generation. In addition, the expulsion and retention of generated petroleum must be considered. However, original quantity (TOC) as well as source rock quality (type) of the source rock must be considered in combination to assess its petroleum generation potential.

From a qualitative point of view, part of this issue includes the assessment of variations in quantitative TOC values that are altered by, for example, thermal maturity, sample collection technique, sample type (cuttings versus core chips), sample quality (e.g., fines only, cavings, contamination), and any high grading of core or cuttings samples. Documented variations in cuttings through the Fayetteville and Chattanooga shales illustrate variations due to sample type and quality as cuttings commonly have mixing effects. An overlying organic-lean sediment will dilute an organic-rich sample often for 10 to 40 ft (3 to 12 m). This is evident in some Fayetteville and Chattanooga wells with cuttings analysis, where the uppermost parts of the organic-rich shales have TOC values suggesting the shale to be organic lean. However, TOC values increase with deeper penetration into the organic-rich shale, to and through the base of the shale, but then also continuing into underlying organic-lean sediments, until finally decreasing to low values.<ref name=Li2010a>Li, P., M. E. Ratchford, and D. M. Jarvie, 2010a, Geochemistry and thermal maturity analysis of the Fayetteville Shale and Chattanooga Shale in the western Arkoma Basin of Arkansas: Arkansas Geological Survey, Information Circular 40, DFF-OG-FS-EAB/ME 012, 58 p.</ref> This is a function of mixing of cuttings while drilling. The same issue in Barnett Shale wells was reported by MEDC,<ref name=St2007 /> who also reported lower vitrinite reflectance values for cuttings than core (sim0.15% Ro lower). The big problem with this mixing effect is that it does not always occur and picking of cuttings does not typically solve the problem in shale-gas resource systems, although it may work in less mature systems. One solution is to minimize the quantitation of the uppermost sections (sim9 m [sim30 ft]) of a shale of interest when cuttings are used for analysis. The inverse of this situation is often identifiable in known organic-lean sediments below an organic-rich shale or [[coal]]. This latter effect is more obvious below coaly intervals, where TOC values will be high unless picked free of coal.

From a qualitative point of view, part of this issue includes the assessment of variations in quantitative TOC values that are altered by, for example, thermal maturity, sample collection technique, sample type (cuttings versus core chips), sample quality (e.g., fines only, cavings, contamination), and any high grading of core or cuttings samples. Documented variations in cuttings through the Fayetteville and Chattanooga shales illustrate variations due to sample type and quality as cuttings commonly have mixing effects. An overlying organic-lean sediment will dilute an organic-rich sample often for 10 to 40 ft (3 to 12 m). This is evident in some Fayetteville and Chattanooga wells with cuttings analysis, where the uppermost parts of the organic-rich shales have TOC values suggesting the shale to be organic lean. However, TOC values increase with deeper penetration into the organic-rich shale, to and through the base of the shale, but then also continuing into underlying organic-lean sediments, until finally decreasing to low values.<ref name=Li2010a>Li, P., M. E. Ratchford, and D. M. Jarvie, 2010a, Geochemistry and thermal maturity analysis of the Fayetteville Shale and Chattanooga Shale in the western Arkoma Basin of Arkansas: Arkansas Geological Survey, Information Circular 40, DFF-OG-FS-EAB/ME 012, 58 p.</ref> This is a function of mixing of cuttings while drilling. The same issue in Barnett Shale wells was reported by MEDC,<ref name=St2007 /> who also reported lower vitrinite reflectance values for cuttings than core (sim0.15% Ro lower). The big problem with this mixing effect is that it does not always occur and picking of cuttings does not typically solve the problem in shale-gas resource systems, although it may work in less mature systems. One solution is to minimize the quantitation of the uppermost sections (sim9 m [sim30 ft]) of a shale of interest when cuttings are used for analysis. The inverse of this situation is often identifiable in known organic-lean sediments below an organic-rich shale or [[coal]]. This latter effect is more obvious below coaly intervals, where TOC values will be high unless picked free of coal.