Water resistivity determination

Development Geology Reference Manual
Series	Methods in Exploration
Part	Wireline methods
Chapter	Determination of water resistivity
Author	Roberto Peveraro
Link	Web page
Store	AAPG Store

The most direct way of finding water resistivity (R_w) is to obtain a sample of formation water and measure its resistivity. However, this is seldom possible in practice, as formation water samples, if available, are invariably contaminated by mud filtrate. R_w is therefore usually calculated, and there are three methods available for this purpose:

• SP method
• Archie equation
• Resistivity ratio method

SP method

Figure 1 Example of a normal SP deflection. Copyright: Schlumberger Educational Services, 1987.

Principle

Figure 2 Example of a reverse SP deflection. (From .)

The first step in the interpretation of the SP log is the establishment of “sand” and “shale” lines, as shown in Figure 1. These are arbitrary limits, with the sand lines normally representing the maximum deflection to the left and shale lines representing the maximum deflection to the right (in shales). Deflections to the left of the shale line are regarded as normal or negative, and correspond to porous and permeable zones containing a more saline interstitial water than the drilling mud (R_w R_mf).

If the mud is more saline than the formation water, the SP currents flow in the opposite direction and the corresponding deflection will be to the right of the shale line. Such a deflection is considered to be reversed or positive (Figure 2). If there is no salinity contrast between the mud and the formation water, no SP currents are generated and no deflection will be observed (SP = 0).

The magnitude of deflection from the shale base line to the maximum deflection developed in a thick, clean, waterbearing sand is referred to as the static SP, or SSP.

Knowledge of the SSP is essential for the derivation of R_w, which is required for the calculation of water saturation in the uninvaded zone. The equation that relates the SSP to measurable quantities, namely, R_w and R_mf, introduces values that are linearly related to their respective chemical activities. These values are referred to as equivalent resistivities and are denoted by R_we and R_mfe. Thus, the standard equation that relates the SSP to the mud filtrate and uninvaded formation water resistivities is

${\mbox{SSP}}={-}K\log \left({\frac {R_{\rm {mfe}}}{R_{\rm {me}}}}\right)$

where K is a constant, the value of which is dependent on the formation temperature. Usually,

$K=61+0.133{\mbox{T}}(^{\circ }{\mbox{F}}){\mbox{ or }}65+0.24{\mbox{T}}(^{\circ }{\mbox{C}})$

Equation 1 is used in the quantitative interpretation of the SP log.

Figure 3 Log used in example of calculation of water resistivity. Copyright: the SP method. (From ; courtesy of Atlas Wireline Division of Western Atlas.

Procedure

The procedure to determine R_w from the SP is outlined as follows. The data required include the SP, the invaded zone resistivity, the formation temperature, and the mud and mud filtrate resistivities at the given formation temperature.

• After selecting on the log the zone in which water resistivity will be determined, the formation temperature is established and the values of mud and mud filtrate resistivity are corrected accordingly.
• The shale and sand lines are established, the bed boundaries on the SP curve are determined, and maximum SP inflection for that permeable bed are read off the log.
• If the bed was too thin for the SP to develop fully (beds thinner than 20 ft), the appropriate correction is applied from the charts.
• Charts supplied by logging companies permit the determination of R_mfe/R_we from the SP and, from that, R_we.
• Finally, the true value of R_w is derived from its equivalent R_we value, again using the appropriate charts.

An example of calculating R_w by using the SP method is as follows. Figure 3 shows the log used in this example. The following charts are required:

	Schlumberger 1989	Western Atlas 1985
Chart 1	GEN-6	1-1
Chart 2	GEN-9	1-5
Chart 3	SP-3	2-1
Chart 4	SP-1	2-2
Chart 5	SP-2	2-3

Given:

• R_m = 2.5 Ω-m at temperature::70°F
• R_mf = 2.0 Ω-m at temperature::70°F
• Hole diameter = 8 in.
• Surface temperature = temperature::60°F
• BHT = temperature::164°F at 10,500 ft

From the log:

• SP deflection = 70 mV
• Bed thickness = 24 ft
• Short normal resistivity = 65 Ω-m

Calculations:

• Bed is from 8114 to depth::8138 ft.
• From Chart 1, using BHT = temperature::164°F at depth::10,500 ft and surface temperature = temperature::60°F: formation temperature T_f at 8100 ft=temperature::140°F.
• From Chart 2, using R_m = 2.5 Ω-m at temperature::70°F and R_mf = 2.0 Ω-m at temperature::70°F: R_m = 1.3 Ω-m at temperature::140°F and R_mf = 1.0 Ω-m at temperature::140°F.
• Shale baseline is two divisions left of depth column.
• Bed thickness is 8138 to depth::8114 ft = length::24 ft.
• SP deflection =–70 mV.
• Use Chart 3 to correct the SP. Use short normal resistivity, R_SN, for invaded-zone resistivity, R_i. This gives R_i/R_m = R_SN/R_m = 65/1.3 = 50. This SP correction factor is 1.07, giving a corrected SP of 1.07 × –70 = –75 mV.
• From Chart 4, using SP corrected and T_f: R_mf/R_we = 9.7.
• R_we = R_mf/(R_mf/R_we) = 1.0/9.7 = 0.103 Ω-m.
• From Chart 5, using R_we and T_f. R_w = 0.103 Ω-m at temperature::140°F (no change).

Assumptions and limitations

It is assumed that ail salts in solution in the fluids are NaCl or equivalent and that the beds are clay free. This method does not work for oil-based muds. Also, it does not give correct estimations of R_w in hydrocarbon-bearing zones.

Archie equation

Principle

If a clean, water-bearing zone is present or can be assumed, R_w can be calculated by using the Archie equation. The zone or permeable bed in which water resistivity is determined is selected on the log. This zone must be 100% water saturated and must not contain any clay or shale. The bed must be thick so that the deep investigation resistivity device is not affected by shoulder beds.

The water saturation equation in general form is

$S_{\rm {w}}{}^{n}={\frac {aR_{\rm {w}}}{\phi ^{m}\,R_{\rm {t}}}}$

Let's assume for a, m, and n the usual initial values of 1, 2, and 2, respectively (although other values for a, m, and n may be more appropriate). We have

$R_{\rm {w}}=S_{\rm {w}}{}^{2}\phi ^{2}\,R_{\rm {t}}$

In a water zone, S_w = 1, thus Equation 4 becomes

$R_{\rm {w}}=\phi ^{2}\,R_{\rm {t}}$

Porosity (ϕ) can be derived from logs. (For more information on methods to derive porosity and the Archie equation, see Standard interpretation. For more on deriving R_t, see Preprocessing of logging data.)

Procedure

The procedure to determine R_w from the Archie Equation is outlined as follows. The data that are required include R_t (or R_o) from deep-reading resistivity tools such as deep induction (ILd) or deep laterolog (LLd) and porosity log(s).

• After correlating logs for depth mismatch, a clean, water-bearing zone is located. If using an induction log, the minimum thickness should be length::15 ft. For a laterolog, the minimum thickness should be length::4 ft.
• Read R_o (= R_f) from the resistivity log, and determine the porosity from logs or otherwise.
• Calculate R_w from Equation (4a).

Assumptions and limitations

It is assumed that there are no clay or conductive minerals in the water-bearing zone, that the zone is clean, and that the invasion is shallow enough for resistivity tools to be unaffected by it. This method only works in clean, waterbearing reservoirs. It is typically unreliable in highly fractured or vuggy reservoirs.

Resistivity ratio method

Principle

In a clean, water-bearing zone, the following relationships can be obtained from application of the Archie equation in the uninvaded and invaded zones:

$R_{\rm {t}}={\frac {aR_{\rm {w}}}{\phi ^{2}S_{\rm {w}}{}^{2}}}$

$R_{\rm {xo}}={\frac {aR_{\rm {mf}}}{\phi ^{2}S_{\rm {xo}}{}^{2}}}$

In such a zone, S_w = S_xo = 1 and a and ϕ are the same in both the flushed and uninvaded zones.

Dividing Equation 5 by Equation 6 gives

${\frac {R_{\rm {t}}}{R_{\rm {xo}}}}={\frac {R_{\rm {w}}}{R_{\rm {mf}}}}$

or

$R_{\rm {w}}={\frac {R_{\rm {t}}}{R_{\rm {xo}}}}R_{\rm {mf}}$

R_t and R_xo are obtained from deep and shallow resistivity logs, and R_mf is at formation temperature.

Procedure

The procedure for determining R_w from the resistivity ratio method is outlined as follows. The data that are required include R_t from ILd or LLd, R_xo from SFL or another shallow-reading resistivity device, R_mf, and T_f.

• After correlating logs for depth mismatch, locate a clean, water-bearing zone. If using an induction log, the minimum thickness should be length::15 ft. For a laterolog, the minimum thickness should be length::4 ft.
• Read R_t and R_xo.
• Correct R_mf to the appropriate formation temperature (T_f) value.
• Calculate R_w from Equation 8.

Figure 4 Example problem showing determination of R_w from resistivity ratio.

Note that an equivalent “quick look” solution can be obtained by an overlay technique using logarithmically scaled R_t and R_xo logs. If one log is placed over the other and shifted so that the two curves coincide in clean, water-bearing zones, the 1 ohm-m line on the R_xo log grid will lie on the R_t grid at a value equal to R_w/R_mf. Since R_mf is known, R_w can then be easily calculated. Figure 4 shows an example of original and shifted logs indicating a R_t/R_mf ratio of 0.45.

Limitations

This method is unreliable in fractured or vuggy reservoirs. It requires a reliable measurement of R_xo. Results can be questionable if the mud resistivity properties have varied significantly after drilling the zone to be analyzed.

Concluding remarks

It is quite common and good practice to determine R_w with more than one method, if possible, to check for consistency and reliability. Variations may occur in the R_w values determined by the three methods outlined here. If this is the case, then the values obtained can be averaged. Once determined, R_w is assumed to be constant throughout the formation being evaluated, unless local knowledge or clear SP log amplitude changes indicate otherwise.

See also

• Difficult lithologies
• Dipmeters
• Formation evaluation of naturally fractured reservoirs
• Basic open hole tools
• Basic tool table
• Introduction to wireline methods
• Preprocessing of logging data
• Wireline formation testers
• Basic cased hole tools
• Standard interpretation
• Quick-look lithology from logs
• Borehole imaging devices

External links

find literature about Water resistivity determination

• Original content in Datapages
• Find the book in the AAPG Store

bottom hole temperature

seating nipple