Changes

Jump to navigation Jump to search
4,593 bytes added ,  16:59, 19 January 2022
m
Line 5: Line 5:  
  | part    = Laboratory methods
 
  | part    = Laboratory methods
 
  | chapter = Capillary pressure
 
  | chapter = Capillary pressure
 +
| frompg  = 221
 +
| topg    = 225
 
  | author  = Charles L. Vavra, John G. Kaldi, Robert M. Sneider
 
  | author  = Charles L. Vavra, John G. Kaldi, Robert M. Sneider
 +
| editor = ''Needs editor''
 
  | link    = http://archives.datapages.com/data/specpubs/methodo1/data/a095/a095/0001/0200/0221.htm
 
  | link    = http://archives.datapages.com/data/specpubs/methodo1/data/a095/a095/0001/0200/0221.htm
 
  | pdf    = http://archives.datapages.com/data/specpubs/methodo1/images/a095/a0950001/0200/02210.pdf
 
  | pdf    = http://archives.datapages.com/data/specpubs/methodo1/images/a095/a0950001/0200/02210.pdf
 
}}
 
}}
Capillary pressure concepts can be used by geologists, petrophysicists, and petroleum engineers to evaluate the following:
+
Capillary pressure concepts can be used by geologists, petrophysicists, and [[petroleum]] engineers to evaluate the following:
 
* Reservoir rock quality
 
* Reservoir rock quality
 
* Pay versus nonpay
 
* Pay versus nonpay
 
* Expected fluid saturations
 
* Expected fluid saturations
* Seal capacity (thickness of hydrocarbon column a seal can hold before it leaks)
+
* Seal capacity (thickness of [[hydrocarbon column]] a seal can hold before it leaks)
 
* Depth of the reservoir [[fluid contacts]]
 
* Depth of the reservoir [[fluid contacts]]
 
* Thickness of the transition zone
 
* Thickness of the transition zone
Line 21: Line 24:     
==Capillary pressure concepts==
 
==Capillary pressure concepts==
Capillary pressure results from interactions of forces acting within and between fluids and their bounding solids. These include both ''cohesive'' forces (surface and interfacial tension) and ''adhesive'' (liquid-solid) forces. When adhesive forces are greater than cohesive forces, the liquid is said to be ''wetting'' (Figure 1a). When cohesive forces exceed adhesive forces, the liquid is ''nonwetting'' (Figure 1b). The relative [[wettability]] of the fluids is described by the ''contact angle'' (θ), which is the angle between the solid and the fluid-fluid interface as measured through the denser fluid (Figure 1). (For information on the measurement of [[wettability]], see the chapter on [[Wettability]]in Part 5.)
+
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_1.jpg|thumb|300px|{{figure_number|1}}Effects of interaction of adhesive and cohesive forces on wettability. (a) If adhesive forces are greater than the cohesive forces, the fluid spreads out on the surface and is termed '''''wetting. '''''(b) If cohesive forces exceed adhesive forces, the liquid beads up and is termed nonwetting. The measure of relative wettability is the contact angle (θ), which is measured through the denser phase.]]
   −
If the end of a narrow capillary tube is placed in a wetting fluid, net adhesive forces draw the fluid into the tube (Figure 2). The wetting phase rises in the capillary above the original interface or ''free surface'' until adhesive and gravitational forces are balanced. Because the wetting and nonwetting fluids have different densities, they also have different pressure gradients (Figure 2). ''Capillary pressure'' (P<sub>c</sub>) is defined as the difference in pressure across the meniscus in the capillary tube. Put another way, capillary pressure is the amount of extra pressure required to force the nonwetting phase to displace the wetting phase in the capillary. Capillary
+
Capillary pressure results from interactions of forces acting within and between fluids and their bounding solids. These include both ''cohesive'' forces (surface and interfacial tension) and ''adhesive'' (liquid-solid) forces. When adhesive forces are greater than cohesive forces, the liquid is said to be ''wetting'' ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_1.jpg|Figure 1a]]). When cohesive forces exceed adhesive forces, the liquid is ''nonwetting'' ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_1.jpg|Figure 1b]]). The relative [[wettability]] of the fluids is described by the ''contact angle'' (&theta;), which is the angle between the solid and the fluid-fluid interface as measured through the denser fluid ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_1.jpg|Figure 1]]).
   −
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_2.png|thumb|The wetting phase rises above the original or free surface in the capillary tube experiment until adhesive and gravitational forces balance. Capillary pressure (P<sub>c</sub>) is the difference in pressure measured across the interface in the capillary (P<sub>c</sub> = ''P''<sub>nw</sub> - ''P''<sub>w</sub>). This pressure results from the contrast in pressure gradients caused by the different densities of the nonwetting (&rho;<sub>nw</sub>) and wetting (&rho;<sub>w</sub>) phases (right).]]
+
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_2.jpg|300px|thumb|{{figure_number|2}}The wetting phase rises above the original or free surface in the capillary tube experiment until adhesive and gravitational forces balance. Capillary pressure (P<sub>c</sub>) is the difference in pressure measured across the interface in the capillary (''P''<sub>c</sub> = ''P''<sub>nw</sub> - ''P''<sub>w</sub>). This pressure results from the contrast in pressure gradients caused by the different densities of the nonwetting (''&rho;''<sub>nw</sub>) and wetting (''&rho;''<sub>w</sub>) phases (right).]]
   −
'''Fig. 1. Effects of interaction of adhesive and cohesive forces on [[wettability]]. (a) If adhesive forces are greater than the cohesive forces, the fluid spreads out on the surface and is termed ''''''''wetting. ''''''''(b) If cohesive forces exceed adhesive forces, the liquid beads up and is termed nonwetting. The measure of relative [[wettability]] is the contact angle (&theta;), which is measured through the denser phase.''' pressure can be calculated as follows:
+
If the end of a narrow capillary tube is placed in a wetting fluid, net adhesive forces draw the fluid into the tube ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_2.jpg|Figure 2]]). The wetting phase rises in the capillary above the original interface or ''free surface'' until adhesive and gravitational forces are balanced. Because the wetting and nonwetting fluids have different densities, they also have different pressure gradients ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_2.jpg|Figure 2]]). ''Capillary pressure'' (''P''<sub>c</sub>) is defined as the difference in pressure across the meniscus in the capillary tube. Put another way, capillary pressure is the amount of extra pressure required to force the nonwetting phase to displace the wetting phase in the capillary. Capillary pressure can be calculated as follows:
   −
:<math>\mathbf{Equation}</math>
+
:<math>P_\mathrm{c} = (\rho_\mathrm{w} - \rho_\mathrm{nw}) g h</math>, or
 +
 
 +
:<math>P_\mathrm{c} = \frac{2\sigma\cos\theta}{r_\mathrm{c}}</math>
    
where
 
where
 
+
* ''&rho;''<sub>w</sub> = density of the wetting nonwetting fluid
* ''&rho;<sub>w</sub>'' = density of the wetting nonwetting fluid<br>&rho;<sub>nw</sub> = density of the nonwetting fluid
+
* ''&rho;''<sub>nw</sub> = density of the nonwetting fluid
 
* ''g'' = gravitational constant
 
* ''g'' = gravitational constant
* ''* h'' = height above the free surface<br>&sigma; = interfacial tension<br>&theta; = contact angle between the fluids and the capillary tube
+
* ''h'' = height above the free surface
* ''r<sub>c</sub>'' = radius of the capillary
+
* ''&sigma;'' = interfacial tension
 +
* ''&theta;'' = contact angle between the fluids and the capillary tube
 +
* ''r''<sub>c</sub> = radius of the capillary
    
These equations show that capillary pressure increases with greater height above the free surface and with smaller capillary size.
 
These equations show that capillary pressure increases with greater height above the free surface and with smaller capillary size.
   −
The importance of capillary pressure in reservoir studies is that many reservoir rocks can be approximated by a bundle of capillaries, with formation water being the wetting phase and hydrocarbons the nonwetting phase. As hydrocarbons begin to migrate into a rock, displacing the pore water, the hydrocarbons first enter the pores with the largest pore throats (capillaries), leaving the wetting phase (water) in the pores with smaller throats or in small nooks and crannies (surface roughness). As the hydrocarbon column increases, the height above the surface where ''P''<sub>c</sub> = 0, called the free surface or ''free water level'' (FWL), becomes greater and the capillary pressure increases, allowing hydrocarbons to enter pores with smaller and smaller throats. This process continues ntil one of several things occurs: (1) generation or migration ends, (2) the trap reaches its spill point, or (3) capillary pressure is sufficient to force hydrocarbons into the seal (displacement pressure is exceeded), allowing the seal to leak.
+
The importance of capillary pressure in reservoir studies is that many reservoir rocks can be approximated by a bundle of capillaries, with formation water being the wetting phase and hydrocarbons the nonwetting phase. As hydrocarbons begin to migrate into a rock, displacing the pore water, the hydrocarbons first enter the pores with the largest pore throats (capillaries), leaving the wetting phase (water) in the pores with smaller throats or in small nooks and crannies (surface roughness). As the hydrocarbon column increases, the height above the surface where ''P''<sub>c</sub> = 0, called the free surface or ''[[free water level]]'' (FWL), becomes greater and the capillary pressure increases, allowing hydrocarbons to enter pores with smaller and smaller throats. This process continues until one of several things occurs:
 +
# [[Petroleum generation|generation]] or migration ends,
 +
# the trap reaches its spill point, or
 +
# capillary pressure is sufficient to force hydrocarbons into the seal ([[top seal displacement pressure|displacement pressure]] is exceeded), allowing the seal to leak.
    +
==Measuring capillary pressure==
 
Reservoir capillary pressure relationships can be evaluated by using either of the following:
 
Reservoir capillary pressure relationships can be evaluated by using either of the following:
 
# Porous plate or centrifuge method, which uses the actual or simulated hydrocarbon-brine system of the reservoir to approximate the wetting properties
 
# Porous plate or centrifuge method, which uses the actual or simulated hydrocarbon-brine system of the reservoir to approximate the wetting properties
 
# Mercury injection, which simulates the premigration wetting characteristics of the reservoir
 
# Mercury injection, which simulates the premigration wetting characteristics of the reservoir
   −
The mercury injection method is recommended to evaluate the initial static distributions of reservoir fluids prior to production because these distributions are typically controlled by the premigration wetting characteristics. Mercury injection is also favored because it is simpler, cheaper, and less time consuming than porous plate or centrifuge methods. In addition, mercury injection can be conducted on cuttings or sidewall samples. Mercury injection capillary pressure data can also be converted to the reservoir fluid system. Although this involves a number of assumptions on [[wettability]] and the effects of cleaning and extracting the core are largely ignored, the cost and time benefits typically favor mercury injection.
+
The mercury injection method is recommended to evaluate the initial static distributions of reservoir fluids prior to production because these distributions are typically controlled by the premigration wetting characteristics. Mercury injection is also favored because it is simpler, cheaper, and less time consuming than porous plate or centrifuge methods. In addition, mercury injection can be conducted on cuttings or sidewall samples. Mercury injection capillary pressure data can also be converted to the reservoir fluid system. Although this involves a number of assumptions on [[wettability]] and the effects of [[Core handling|cleaning and extracting the core]] are largely ignored, the cost and time benefits typically favor mercury injection.
    
==Terminology and mercury injection systematics==
 
==Terminology and mercury injection systematics==
Mercury injection capillary pressure data are acquired by injecting mercury into an evacuated, cleaned, and extracted core plug. Mercury injection pressure is increased in a stepwise manner, and the percentage of rock pore volume saturated by mercury at each step is recorded after allowing sufficient time for equilibrium to be reached. The pressure is then plotted against the mercury saturation (Figure 3), resulting in the injection curve (which is also called the drainage curve because the wetting phase is being drained from the sample).
     −
The pressure at which mercury first enters the sample (after the mercury has filled any surface irregularities on the sample) is termed the ''displacement pressure'' (P<sub>d</sub>). The percentage of pore volume saturated by mercury at the maximum pressure is the ''maximum saturation'' (S<sub>max</sub>). The unsaturated pore volume at that pressure is the ''minimum unsaturated pore volume'' (u<sub>min</sub>) (Figure 3). This is sometimes incorrectly referred to as irreducible saturation. This term is inappropriate for the air-mercury system because saturation depends on applied pressure and on the duration of the experiment (Wardlaw and<ref name=Wardlaw_etal_1976>Wardlaw, N. C., and R. P. Taylor, 1976, Mercury capillary pressure curves and the interpretation of pore structures and capillary behavior in reservoir rocks: Bulletin of Canadian Petroleum Geology, v. 24, p. 225-262.</ref>.
+
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.jpg|300px|thumb|{{figure_number|3}}Mercury injection capillary pressure curve terminology.]]
 +
 
 +
Mercury injection capillary pressure data are acquired by injecting mercury into an evacuated, cleaned, and extracted core plug. Mercury injection pressure is increased in a stepwise manner, and the percentage of rock pore volume saturated by mercury at each step is recorded after allowing sufficient time for equilibrium to be reached. The pressure is then plotted against the mercury saturation ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.jpg|Figure 3]]), resulting in the injection curve (which is also called the drainage curve because the wetting phase is being drained from the sample).
   −
After the maximum pressure is reached, the pressure is reduced in steps and air (the wetting phase) is allowed to imbibe into the sample. The amount of mercury expelled from the sample at each pressure is expressed as a percentage of total pore volume or bulk volume. Again, pressure is plotted against mercury saturation in the withdrawal curve (Figure 3). The volume of pore space still saturated with mercury after pressure is reduced to the minimum is called ''the residual mercury saturation'' (S<sub>R</sub>).
+
The pressure at which mercury first enters the sample (after the mercury has filled any surface irregularities on the sample) is termed the ''[[displacement pressure]]'' (''P''<sub>d</sub>). The percentage of pore volume saturated by mercury at the maximum pressure is the ''maximum saturation'' (''S''<sub>max</sub>). The unsaturated pore volume at that pressure is the ''minimum unsaturated pore volume'' (''u''<sub>min</sub>) ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.jpg|Figure 3]]). This is sometimes incorrectly referred to as [http://petrowiki.org/Glossary%3AIrreducible_water_saturation irreducible saturation]. This term is inappropriate for the air-mercury system because saturation depends on applied pressure and on the duration of the experiment.<ref name=Wardlaw_etal_1976 />
   −
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.png|thumb|Mercury injection capillary pressure curve terminology.]]
+
After the maximum pressure is reached, the pressure is reduced in steps and air (the wetting phase) is allowed to imbibe into the sample. The amount of mercury expelled from the sample at each pressure is expressed as a percentage of total pore volume or bulk volume. Again, pressure is plotted against mercury saturation in the withdrawal curve ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.jpg|Figure 3]]). The volume of pore space still saturated with mercury after pressure is reduced to the minimum is called ''the residual mercury saturation'' (S<sub>R</sub>).
    
Data from the mercury injection curve can be used to approximate the distribution of pore volume accessible by throats of given effective radii (in cm) using the following equation:
 
Data from the mercury injection curve can be used to approximate the distribution of pore volume accessible by throats of given effective radii (in cm) using the following equation:
   −
:<math>\mathbf{Equation}</math>
+
:<math>r\mathrm{c} = \frac{2\sigma\cos\theta}{P_\mathrm{c}}</math>
    
where
 
where
 +
* ''&sigma;'' = interfacial tension of the air-mercury system (480 dynes/cm)
 +
* ''&theta;'' = air/mercury/solid contact angle (140&deg;)
 +
* ''P''<sub>c</sub> = capillary pressure in dynes/cm<sup>2</sup> (1 psi = 69035 dynes/cm<sup>2</sup>)
   −
* ''&sigma;'' = interfacial tension of the air-mercury system (480 dynes/cm)<br>&theta; = air/mercury/solid contact angle (140&deg;)
+
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_4.jpg|thumb|300px|{{figure_number|4}}Idealized mercury injection capillary pressure curve shapes. Note that all of the curves have identical displacement pressures and minimum unsaturated pore volumes, but that the saturation profiles would differ dramatically due to differences in pore throat size distributions.]]
* ''P<sub>c</sub>'' = capillary pressure in dynes/cm<sup>2</sup> (1 psi = 69035 dynes/cm<sup>2</sup>)
     −
Note that this equation calculates the radius of a cylindrical capillary tube; however, real pore throats have very complex geometries. Therefore, the calculated values represent the ''effective'' radii of the pore throats, which may not equal their actual dimensions. Samples dominated by throats of similar size (well sorted) have broad, flat plateaus (Figure 4). As sorting becomes poorer, the plateau steepens then disappears and the slope of the curve approaches 45_ (unsorted).
+
Note that this equation calculates the radius of a cylindrical capillary tube; however, real pore throats have very complex geometries. Therefore, the calculated values represent the ''effective'' radii of the pore throats, which may not equal their actual dimensions. Samples dominated by throats of similar size (well sorted) have broad, flat plateaus ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_4.jpg|Figure 4]]). As [[Core_description#Maturity|sorting] becomes poorer, the plateau steepens then disappears and the slope of the curve approaches 45&deg; (unsorted).
   −
Data from the mercury withdrawal (air imbibition) curve can provide information regarding the efficiency with which the nonwetting phase can be withdrawn from the pore system. ''Withdrawal efficiency'' (W<sub>E</sub>) is defined as the ratio of the mercury saturation in the sample at minimum pressure after pressure is reduced (S<sub>R</sub>) to the saturation at maximum pressure (S<sub>max</sub>) (Figure 3) (Wardlaw and<ref name=Wardlaw_etal_1976 />. Because few samples reach 100% mercury saturation at routinely available injection pressures, data are normalized by the following equation:
+
Data from the mercury withdrawal (air imbibition) curve can provide information regarding the efficiency with which the nonwetting phase can be withdrawn from the pore system. ''Withdrawal efficiency'' (''W''<sub>E</sub>) is defined as the ratio of the mercury saturation in the sample at minimum pressure after pressure is reduced (''S''<sub>R</sub>) to the saturation at maximum pressure (''S''<sub>max</sub>) ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.jpg|Figure 3]]).<ref name=Wardlaw_etal_1976 /> Because few samples reach 100% mercury saturation at routinely available injection pressures, data are normalized by the following equation:
   −
:<math>\mathbf{Equation}</math>
+
:<math>W_\mathrm{E} = \frac{S_\mathrm{max} - S\mathrm{R}}{S_\mathrm{max}} \times 100%</math>
    
Withdrawal efficiency in the air-mercury system is controlled exclusively by pore geometry, which can be interpreted from the capillary pressure curves and by direct observation of the rock or an epoxy resin pore cast. Critical pore geometry factors affecting withdrawal efficiency include effective pore throat heterogeneity; the ratio of pore body to pore throat size (r<sub>b</sub>/r<sub>t</sub>); and the number of throats connecting each pore (coordination number). Table 1 shows the effect of these parameters on withdrawal efficiency.
 
Withdrawal efficiency in the air-mercury system is controlled exclusively by pore geometry, which can be interpreted from the capillary pressure curves and by direct observation of the rock or an epoxy resin pore cast. Critical pore geometry factors affecting withdrawal efficiency include effective pore throat heterogeneity; the ratio of pore body to pore throat size (r<sub>b</sub>/r<sub>t</sub>); and the number of throats connecting each pore (coordination number). Table 1 shows the effect of these parameters on withdrawal efficiency.
   −
Relating withdrawal efficiency in the air-mercury system to recovery efficiency in the hydrocarbon-water system is dependent on properties of the fluids as well as properties of the pore system. Fluid properties that affect recovery include viscosity, density, interfacial tension, [[wettability]], contact angle hysteresis, and rate of displacement (Wardlaw and<ref name=Wardlaw_etal_1978>Wardlaw, N. C., and J. P. Cassan, 1978, Estimation of recovery efficiency by visual observation of pore systems in reservoir rocks: Bulletin of Canadian Petroleum Geology, v. 26, p. 572-585.</ref>. Nevertheless, for a given range of fluid properties in a water wet reservoir, the same pore geometry factors that contribute to increased mercury withdrawal efficiency also increase hydrocarbon recovery efficiency.
+
{| class="wikitable"
 +
|+ {{table_number|1}}Pore geometry factors affecting recovery efficiency
 +
|-
 +
! Factor || High RE || Low RE
 +
|-
 +
| Pore throat heterogeneity || Low || High
 +
|-
 +
| Pore body to pore throat size ratio || Low || High
 +
|-
 +
| Coordination number || High || Low
 +
|}
 +
 
 +
Relating withdrawal efficiency in the air-mercury system to recovery efficiency in the hydrocarbon-water system is dependent on properties of the fluids as well as properties of the pore system. Fluid properties that affect recovery include [[viscosity]], density, interfacial tension, [[wettability]], contact angle hysteresis, and rate of displacement.<ref name=Wardlaw_etal_1978 /> Nevertheless, for a given range of fluid properties in a water wet reservoir, the same pore geometry factors that contribute to increased mercury withdrawal efficiency also increase hydrocarbon recovery efficiency.
    
==Reservoir applications==
 
==Reservoir applications==
===Conversion from Air-Mercury to Brine-Hydrocarbon System===
+
===Conversion from air-mercury to brine-hydrocarbon system===
 
Before mercury injection data can be applied to reservoirs, the data must be converted from the air-mercury system to the brine-hydrocarbon system of the reservoir using the following relationship:
 
Before mercury injection data can be applied to reservoirs, the data must be converted from the air-mercury system to the brine-hydrocarbon system of the reservoir using the following relationship:
   −
:<math>\mathbf{Equation}</math>
+
:<math>P_\mathbf{C_{b/hc}} = P_\mathbf{C_{a/m}} \times \frac{\sigma_\mathrm{b/hc}\cos\theta_\mathrm{b/hc}}{\sigma_\mathrm{a/m}\cos\theta_\mathrm{a/m}} </math>
    
where
 
where
 
+
* ''P''<sub>C<sub>b/hc</sub></sub> = capillary pressure in the brine-hydrocarbon system of the reservoir
* ''P<sub>Cb</sub>hc/'' = capillary pressure in the brine-hydrocarbon system of the reservoir
+
* ''P''<sub>C<sub>a/m</sub></sub> = capillary pressure in the air-mercury system
* ''P<sub>Ca</sub>m/'' = capillary pressure in the air-mercury system<br>&sigma;<sub>b</sub>hc/ = interfacial tension of the brine-hydrocarbon system<br>&sigma;<sub>a</sub>m/ = interfacial tension of air-mercury system<br>&theta;<sub>b</sub>hc/ = contact angle of the brine-hydrocarbon-solid system<br>&theta;<sub>a</sub>m/ = contact angle of the air-mercury-solid system
+
* ''&sigma;''<sub>b/hc</sub> = interfacial tension of the brine-hydrocarbon system
 +
* ''&sigma;''<sub>a/m</sub> = interfacial tension of air-mercury system
 +
* ''&theta;''<sub>b/hc</sub> = contact angle of the brine-hydrocarbon-solid system
 +
* ''&theta;''<sub>a/m</sub> = contact angle of the air-mercury-solid system
    
Ideally, values for brine-hydrocarbon contact angle, surface tension, and fluid densities at reservoir temperature and pressure should be determined in the laboratory using actual reservoir fluids. However, these measurements are difficult and expensive, so approximations such as those given in Tables 2 and 3 are commonly used.
 
Ideally, values for brine-hydrocarbon contact angle, surface tension, and fluid densities at reservoir temperature and pressure should be determined in the laboratory using actual reservoir fluids. However, these measurements are difficult and expensive, so approximations such as those given in Tables 2 and 3 are commonly used.
   −
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_4.png|thumb|Idealized mercury injection capillary pressure curve shapes. Note that all of the curves have identical displacement pressures and minimum unsaturated pore volumes, but that the saturation profiles would differ dramatically due to differences in pore throat size distributions.]]
+
{| class="wikitable"
 +
|+ {{table_number|2}}Typical contact angle and surface tension values*
 +
|-
 +
! System || Contact angle<br />''&theta;''| || Interfacial tension<br />''&sigma;'' [dyn/cm<sup>3</sup>]
 +
|-
 +
| Air–brine || 0&deg; || 72
 +
|-
 +
| Air–mercury || 140&deg; || 480
 +
|-
 +
| [[Crude oil]]–water || 0&deg; || 35
 +
|}
 +
''<small>* Contact angle is measured on a [[quartz]] plane during drainage</small>''
   −
[[File:table_charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_1.png|thumb|Pore geometry factors affecting recovery efficiency (RE)]]
+
{| class="wikitable"
 +
|+ {{table_number|3}}Typical fluid density ranges
 +
|-
 +
! Fluid || Density range<br />''&rho;'' [g/cm<sup>3</sup>]
 +
|-
 +
| Gas || 0.00073 to 0.50
 +
|-
 +
| Oil || 0.50 to 1.0
 +
|-
 +
| Brine || 1.0 to 1.2
 +
|}
    
===Height above the free water level===
 
===Height above the free water level===
 +
 +
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_5.jpg|thumb|300px|{{figure_number|5}}Effect of capillary pressure (left) on water saturation (right). At any given height above the free water level, water saturations vary widely among rock types (A-E) due to diffferences in capillarity. For example, at 50 ft above free water level, water saturations vary from 18% (rock type A) to 95% (rock type E). A well drilled into an interbedded sequence of these rock types would show multiple oil-water contacts and a highly irregular vertical saturation profile. Note also the wide transition zone in rock type B caused by poor sorting of the pore throats.]]
 +
 
Having converted the capillary pressure data to the hydrocarbon-brine system of the reservoir and knowing the hydrocarbon and brine densities from laboratory analysis, we can now calculate the amount of hydrocarbon column required (height above the free water level or level where ''P''<sub>c</sub> = 0) to attain a pressure of interest:
 
Having converted the capillary pressure data to the hydrocarbon-brine system of the reservoir and knowing the hydrocarbon and brine densities from laboratory analysis, we can now calculate the amount of hydrocarbon column required (height above the free water level or level where ''P''<sub>c</sub> = 0) to attain a pressure of interest:
   −
:<math>\mathbf{Equation}</math>
+
:<math>h = \frac{P_\mathbf{h}}{0.433(\rho_\mathrm{b} - \rho_\mathrm{hc})}</math>
    
where
 
where
   
* ''h'' = height above the free water level (in ft)
 
* ''h'' = height above the free water level (in ft)
* ''P<sub>c</sub>'' = hydrocarbon-brine capillary pressure (in psi)<br>&rho;<sub>b</sub> = specific density of brine at ambient conditions (in gm/cm<sup>3</sup>)<br>&rho;<sub>hc</sub> = specific density of hydrocarbons at ambient conditions (in gm/cm<sup>3</sup>)
+
* ''P''<sub>c</sub> = hydrocarbon-brine capillary pressure (in psi)
* ''0.433'' = the gradient of pure water at ambient conditions
+
* ''&rho;''<sub>b</sub> = specific density of brine at ambient conditions (in gm/cm<sup>3</sup>)
 +
* ''&rho;''<sub>hc</sub> = specific density of hydrocarbons at ambient conditions (in gm/cm<sup>3</sup>)
 +
* 0.433 = the gradient of pure water at ambient conditions
   −
This information can be used to compare expected fluid saturations of different rock types at given levels in the reservoir (Figure 5). (For information on the application of capillary pressure data to evaluating [[fluid contacts]], see the chapter on [[Fluid contacts]] in Part 6.)
+
This information can be used to compare expected fluid saturations of different rock types at given levels in the reservoir ([[:File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_5.jpg|Figure 5]]). (For information on the application of capillary pressure data to evaluating [[fluid contacts]].
    
===Evaluating seal capacity===
 
===Evaluating seal capacity===
 
If the capillary pressure data from the suspected seal are available or can be estimated, the maximum hydrocarbon column each rock type could have before the seal begins leaking can be calculated by the following:
 
If the capillary pressure data from the suspected seal are available or can be estimated, the maximum hydrocarbon column each rock type could have before the seal begins leaking can be calculated by the following:
   −
:<math>\mathbf{Equation}</math>
+
:<math>h_\mathrm{max} = \frac{P_\mathbf{dS} - P_\mathrm{dR}}{0.433(\rho_\mathrm{w} - \rho_\mathrm{hc})}</math>
    
where
 
where
   
* ''h<sub>max</sub>'' = height of the hydrocarbon column (in feet)
 
* ''h<sub>max</sub>'' = height of the hydrocarbon column (in feet)
 
* ''P<sub>dS</sub>'' = brine-hydrocarbon displacement pressure of the seal (in psi)
 
* ''P<sub>dS</sub>'' = brine-hydrocarbon displacement pressure of the seal (in psi)
 
* ''P<sub>dR</sub>'' = brine-hydrocarbon displacement pressure of the reservoir rock (in psi)
 
* ''P<sub>dR</sub>'' = brine-hydrocarbon displacement pressure of the reservoir rock (in psi)
   −
===Additional applications===
+
It is difficult to determine the [[Top seal displacement pressure|displacement pressure (P<sub>d</sub>) of a top seal]].
Capillary pressure data can also be applied to help distinguish reservoir from nonreservoir and pay from nonpay (see [[Effective pay determination]]). Several workers have attempted to correlate capillary pressure data and brine or air permeabilities. Purcell related capillary pressures empirically to air [[permeability]] through the graphical integral of the curve of mercury saturation versus reciprocal capillary pressure squared. Swanson (1981)<ref name=Swanson_1981>Swanson, R. G., 1981, Sample examination manual:AAPG Methods in Exploration Series, 35 p.</ref> proposed a simple nomograph whose application improved estimation of brine [[permeability]] from capillary pressure measurements on sidewall cores and ditch cuttings.
     −
Another type of mercury test involves injecting mercury to a saturation less than the maximum, withdrawing the mercury to some residual wetting phase saturation, and then reinjecting the mercury. This process, repeated several times to progressively higher maximum pressures, produces hysteresis loops. These loops, wherein mercury is partially withdrawn and then reinjected, can be used to investigate withdrawal efficiency at various initial saturations (Morrow, 1970<ref name=Morrow_1970>Morrow, N. R., 1970, Irreducible wetting phase saturations in porous media: Chemical Engineering Science, v. 25, p. 1799-1815.</ref>; Melrose and Brandner, 1974<ref name=Melrose_etal_1974>Melrose, J. C., and C. F. Brandner, 1974, Role of capillary forces in determining microscopic displacement efficiency for oil recovery by [[waterflooding]]: Journal Canadian Petroleum Technology, v. 13, p. 54-62.</ref>; Wardlaw and Taylor, 1976<ref name=Wardlaw_etal_1976 />; Wardlaw and Cassan, 1978<ref name=Wardlaw_etal_1978 />; Wardlaw et al., 1988<ref name=Wardlaw_etal_1988 />). Results suggest that the higher the initial saturation of the nonwetting phase, the greater the withdrawal efficiency. Porosimetry uses hysteresis loops to interpret pore body and pore throat size distributions and their patial arrangement (Dullien and Dhawan, 1974<ref name=Dullien_etal_1974>Dullien, F. A. L., and G. K. Dhawan, 1974, Characterization of pore structure by a combination of quantitative photomicrography and mercury porosimetry: Journal Colloid and Interface Science, v. 47, p. 337-349.</ref>; Wardlaw et al., 1988<ref name=Wardlaw_etal_1988 />).
+
* First, [[seal capacity]] is based on the presence of a single, continuous, high-P<sub>d</sub> layer, not upon an arithmetic average of all P<sub>d</sub> values. The trapping capacity is determined by the highest displacement pressure within a seal, theoretically even if that interval is a layer only one grain thick. A 500-m-thick siltstone may appear incapable of trapping more than [[length::1 m]] of hydrocarbon. The presence of a 1-cm-thick claystone layer, however, may create a seal for thousands of meters of hydrocarbon. Predicting these local seals is difficult and adds a measure of risk to any evaluation of intact top seals using capillary theory.
 +
* Second, experiments demonstrate that hydrocarbon [[migration]] through a seal does not occur along a broad, uniform front but along narrow fingers reflecting local, tortuous pathways of low displacement pressure.<ref name=ch10r17>Dembecki, H., Jr., Anderson, M., J., 1989, [http://archives.datapages.com/data/bulletns/1988-89/data/pg/0073/0008/1000/1018.htm Secondary migration of oil: experiments supporting efficient movement of separate, buoyant oil phase along limited conduits]: AAPG Bulletin, vol. 73, no. 8, p. 1018–1021.</ref><ref name=ch10r12>CatalanXiaown, L., F., Chatzis, I., Dullien, F., A., L., 1992, [http://archives.datapages.com/data/bulletns/1992-93/data/pg/0076/0005/0000/0638.htm An experimental study of secondary oil migration]: AAPG Bulletin, vol. 76, no. 5, p. 638–650.</ref>
   −
It should be noted that although these more specialized procedures are quite informative, especially for approximating hydrocarbon recovery efficiencies, they are also relatively labor intensive and expensive when compared to routine mercury injection tests.
+
These tortuous pathways develop even in bead packs of uniform, closely packed glass spheres. Natural seals are even more heterogeneous.
   −
[[File:table_charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_2.png|thumb|Typical contact angle and surface tension values]]
+
The difficulty of defining these narrow zones during sampling complicates our ability to predict the critical displacement pressure of a seal. Although 99% of the samples from a trap may indicate a top seal capable of trapping a 500-m oil column, the seal may well leak through a narrow pathway only centimeters in diameter.
   −
[[File:table_charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_3.png|thumb|Typical fluid density ranges]]  
+
===Additional applications===
 +
Capillary pressure data can also be applied to help distinguish reservoir from nonreservoir and pay from nonpay (see [[Effective pay determination]]). Several workers have attempted to correlate capillary pressure data and brine or air permeabilities. Purcell related capillary pressures empirically to air [[permeability]] through the graphical integral of the curve of mercury saturation versus reciprocal capillary pressure squared. Swanson<ref name=Swanson_1981>Swanson, R. G., 1981, Sample examination manual: [http://store.aapg.org/detail.aspx?id=603 AAPG Methods in Exploration 1], 35 p.</ref> proposed a simple nomograph whose application improved estimation of brine [[permeability]] from capillary pressure measurements on sidewall cores and ditch cuttings.
   −
[[File:charles-l-vavra-john-g-kaldi-robert-m-sneider_capillary-pressure_5.png|thumb|Effect of capillary pressure (left) on water saturation (right). At any given height above the free water level, water saturations vary widely among rock types (A-E) due to diffferences in capillarity. For example, at 50 ft above free water level, water saturations vary from 18% (rock type A) to 95% (rock type E). A well drilled into an interbedded sequence of these rock types would show multiple oil-water contacts and a highly irregular vertical saturation profile. Note also the wide transition zone in rock type B caused by poor sorting of the pore throats.]]
+
Another type of mercury test involves injecting mercury to a saturation less than the maximum, withdrawing the mercury to some residual wetting phase saturation, and then reinjecting the mercury. This process, repeated several times to progressively higher maximum pressures, produces hysteresis loops. These loops, wherein mercury is partially withdrawn and then reinjected, can be used to investigate withdrawal efficiency at various initial saturations.<ref name=Morrow_1970>Morrow, N. R., 1970, [http://www.sciencedirect.com/science/article/pii/0009250970800707 Irreducible wetting phase saturations in porous media]: Chemical Engineering Science, v. 25, p. 1799-1815.</ref> <ref name=Melrose_etal_1974>Melrose, J. C., and C. F. Brandner, 1974, Role of capillary forces in determining microscopic displacement efficiency for oil recovery by [[waterflooding]]: Journal Canadian Petroleum Technology, v. 13, p. 54-62.</ref> <ref name=Wardlaw_etal_1976>Wardlaw, N. C., and R. P. Taylor, 1976, Mercury capillary pressure curves and the interpretation of pore structures and capillary behavior in reservoir rocks: Bulletin of Canadian Petroleum Geology, v. 24, p. 225-262.</ref> <ref name=Wardlaw_etal_1978>Wardlaw, N. C., and J. P. Cassan, 1978, Estimation of recovery efficiency by visual observation of pore systems in reservoir rocks: Bulletin of Canadian Petroleum Geology, v. 26, p. 572-585.</ref> <ref name=Wardlaw_etal_1988>Wardlaw, N. C., M. McKellar, and Y. Li, 1988, Pore and throat size distribution determined by mercury porosimetry and by direct observation: Carbonates and Evaporites, v. 3, p. 1-15.</ref> Results suggest that the higher the initial saturation of the nonwetting phase, the greater the withdrawal efficiency. Porosimetry uses hysteresis loops to interpret pore body and pore throat size distributions and their partial arrangement.<ref name=Dullien_etal_1974>Dullien, F. A. L., and G. K. Dhawan, 1974, Characterization of pore structure by a combination of quantitative photomicrography and mercury porosimetry: Journal Colloid and Interface Science, v. 47, p. 337-349.</ref> <ref name=Wardlaw_etal_1988 /> Pore sizes have also been evaluated with rate-controlled mercury injection.<ref name=Yuan_etal_1986>Yuan, H. H., and B. F. Swanson, 1986, [https://www.onepetro.org/journal-paper/SPE-14892-PA Resolving pore space characteristics by rate-controlled porosimetry]: 5th Symposium on [[Enhanced oil recovery]] of the Society of Petroleum Engineers and the Department of Energy, April, SPE/DOE 14892, 9 p.</ref>
 +
 
 +
It should be noted that although these more specialized procedures are quite informative, especially for approximating hydrocarbon recovery efficiencies, they are also relatively labor intensive and expensive when compared to routine mercury injection tests.
    
==See also==
 
==See also==
* [[Core description]]
+
 
* [[Introduction to laboratory methods]]
+
* [[Relative permeability and pore type]]
* [[Relative permeability]]
  −
* [[Paleontology]]
   
* [[Wettability]]
 
* [[Wettability]]
 
* [[Oil and condensate analysis]]
 
* [[Oil and condensate analysis]]
 
* [[Oilfield water analysis]]
 
* [[Oilfield water analysis]]
 
* [[Permeability]]
 
* [[Permeability]]
* [[Thin section analysis]]
   
* [[Overview of routine core analysis]]
 
* [[Overview of routine core analysis]]
 
* [[Core-log transformations and porosity-permeability relationships]]
 
* [[Core-log transformations and porosity-permeability relationships]]
* [[Sem, xrd, cl, and xf methods]]
+
* [[Rock-water reaction]]
    
==References==
 
==References==
Line 153: Line 206:  
* [[seg:Dictionary:Capillary pressure|Dictionary:Capillary pressure]] in Sheriff's Encyclopedic Dictionary
 
* [[seg:Dictionary:Capillary pressure|Dictionary:Capillary pressure]] in Sheriff's Encyclopedic Dictionary
   −
[[Category:Laboratory methods]] [[Category:Test content]][[Category:Pages with unformatted equations]][[Category:Pages with unformatted tables]]
+
[[Category:Laboratory methods]]
 +
[[Category:Methods in Exploration 10]]

Navigation menu