Magnetics: interpreting residual maps

From AAPG Wiki
Jump to navigation Jump to search
Exploring for Oil and Gas Traps
Series Treatise in Petroleum Geology
Part Predicting the occurrence of oil and gas traps
Chapter Using magnetics in petroleum exploration
Author Edward A. Beaumont, S. Parker Gay
Link Web page
Store AAPG Store

Amajor pitfall in interpreting magnetic residual maps is assuming that magnetic highs and lows are caused by elevation changes on basement rocks in a sedimentary basin. To the contrary, most magnetic anomalies are caused by lithologic changes and the corresponding changes in susceptibility. As shown in Figure 14-5, the basement is of complex lithology and is highly fractured. The fractures divide the basement into blocks and are zones of weakness along which faults occur. The most important and most reliable information obtainable from aeromagnetic maps is the configuration (in plan view) of the underlying basement fault block pattern.

Interpreting depth to basement

It is futile to attempt to define accurately the vertical dimension, Z, of adjacent source bodies with magnetics because of the inherent ambiguity of potential field methods in determining Z (see, e.g. .[1] Furthermore, seismic and subsurface methods measure depth so much more accurately than magnetics that it is unwise to try to compete with these excellent techniques. This is not to say, however, that we should not use magnetics to estimate the approximate thickness of the sedimentary section in a new basin, i.e., in determining whether it is 2, 5, or length::10 km thick, for example, to a usual accuracy of about ±15% under favorable conditions.

Interpreting fault throw

There is a fairly reliable way to determine the direction of throw of certain basement faults from magnetic maps. Faults that vertically offset basement or other magnetic sources generally show abrupt amplitude changes of magnetic anomalies, both the highs and lows. In the figure below, a series of four northeast-trending magnetic anomalies on the west (two highs, two lows) abruptly loses amplitude along a northwest-trending line (A–A′) that crosscuts them. The high and low magnetic trends can be identified easily on both sides of this obvious down-to-the-east fault. The four anomalies disappear altogether along another northwest-trending line farther east (B–B′). This may be a strike-slip fault, which is not common in this area, or another down-to-the-east fault that has down-dropped the four anomalies beneath the level of detection—the preferred interpretation.

Interpreting shear zones

Figure 1 residual aeromagnetic map of an area on the north shelf of the Anadarko basin in Oklahoma where the sedimentary section is approximately 3.6 km (12,000 ft) thick and basement lies about 3.8 km (12,500 ft) beneath flight level.

Figure 1 shows a residual aeromagnetic map of an area on the north shelf of the Anadarko basin in Oklahoma where the sedimentary section is approximately 3.6 km (12,000 ft) thick and basement lies about 3.8 km (12,500 ft) beneath flight level. The residual magnetic contours (a) are shown at a 2-nT interval. The interpreted shear zones are traced along the linear gradients separating the residual magnetic highs and lows and along truncation lines of anomalies. On the right figure (b), two faults located from subsurface mapping are shown, labeled U/D. The evidence for their existence is seen in subsurface mapping. Both are located exactly along the interpreted basement shear zones, or block boundaries, as represented by gradients on the magnetic map. Note, however, that most of the interpreted basement shear zones in this area have no corresponding overlying faults. These zones were never reactivated—at least not sufficiently enough to be detected by the existing subsurface data.

Oil field example

Figure 2 .

In Figure 2, also note the structural high apparent in Devonian strata about length::800 m (2500 ft) above basement in the West Campbell field, conveniently nestled between block boundaries. Block boundaries, i.e., shear zones, generally erode low, so it follows that the interiors of blocks must, in many cases, correspond to basement topographic highs. West Campbell field appears to be a case in point and is most likely underlain by such a basement topographic prominence, although there are no wells to basement here to document it. The culmination of structural closure nearer the north end of the block rather than at its center is probably due to the south dip of basement in this area.

Interpreting fault location

Figure 3 Details from Gatewood.[2]

Figure 3 is a residual magnetic map of another area in northern Oklahoma with faults superimposed. Here the sedimentary section is approximately length::2 km (6500 ft) thick, and the flight level was about length::2.3 km (7500 ft) above basement. The faults shown were interpreted from a detailed subsurface study by Geomap Inc. The faults were mapped about length::500 m (1600 ft) above basement and show 30–90 m (100–300 ft) of displacement. Note the high degree of correlation between these faults and the residual magnetic gradients corresponding to the interpreted basement shear zones. Some 64% of the total length of faults, in fact, lies on the predicted shear zones following magnetic gradients. Note also that many magnetic gradients in Figure 14-11 show no faults cutting the section. These may not have been reactivated.

See also

References

  1. Skeels, D., C., 1947, Ambiguity in gravity interpretation: Geophysics, vol. 12, p. 43–56., 10., 1190/1., 1437295
  2. Gatewood, L., 1983, Viola–Bromide and Oil Creek Structure (map): Oklahoma City, privately sold and distributed.

External links

find literature about
Magnetics: interpreting residual maps
Datapages button.png GeoScienceWorld button.png OnePetro button.png Google button.png