Difference between revisions of "Percent fill: controlling factors"
Jump to navigation
Jump to search
Cwhitehurst (talk | contribs) |
Cwhitehurst (talk | contribs) m (added Category:Treatise Handbook 3 using HotCat) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 6: | Line 6: | ||
| part = Predicting the occurrence of oil and gas traps | | part = Predicting the occurrence of oil and gas traps | ||
| chapter = Evaluating top and fault seal | | chapter = Evaluating top and fault seal | ||
| − | | frompg = 10- | + | | frompg = 10-16 |
| − | | topg = 10- | + | | topg = 10-16 |
| author = Grant M. Skerlec | | author = Grant M. Skerlec | ||
| link = http://archives.datapages.com/data/specpubs/beaumont/ch10/ch10.htm | | link = http://archives.datapages.com/data/specpubs/beaumont/ch10/ch10.htm | ||
| Line 17: | Line 17: | ||
* Top seal capacity/integrity | * Top seal capacity/integrity | ||
| − | * Synclinal spill points | + | * [[Syncline|Synclinal]] spill points |
| − | * Charge | + | * [[Calculating charge volume|Charge]] |
* Fault seal capacity | * Fault seal capacity | ||
* Fault-dependent leak points | * Fault-dependent leak points | ||
| Line 24: | Line 24: | ||
==Control summary== | ==Control summary== | ||
| − | [[file:evaluating-top-and-fault-seal_fig10-14.png|300px|thumb|{{figure number|1}}Controls on percent fill and hydrocarbon column height | + | [[file:evaluating-top-and-fault-seal_fig10-14.png|300px|thumb|{{figure number|1}}Controls on percent fill and hydrocarbon column height.]] |
| − | [[:file:evaluating-top-and-fault-seal_fig10-14.png|Figure 1]] summarizes the various controls on percent fill and hydrocarbon column height. The maximum fill case is the synclinal spill point (SSP). A cross-leaking fault limits the percent fill to the juxtaposed lithology leak point (JLLP). A dip-leaking fault limits the percent fill to the fault plane leak point (FPLP). | + | [[:file:evaluating-top-and-fault-seal_fig10-14.png|Figure 1]] summarizes the various controls on percent fill and [[hydrocarbon column]] height. The maximum fill case is the synclinal spill point (SSP). A [[cross-leaking fault]] limits the percent fill to the juxtaposed lithology leak point (JLLP). A [[dip]]-leaking fault limits the percent fill to the fault plane leak point (FPLP). |
| − | A cross-sealing fault allows fill below the JLLP and possibly as deep as the SSP. A trap also may be partially filled (PF) due to either charge or top seal capacity. A partially filled trap can have a hydrocarbon contact at any depth. | + | A [[cross-sealing fault]] allows fill below the JLLP and possibly as deep as the SSP. A trap also may be partially filled (PF) due to either charge or top seal capacity. A partially filled trap can have a [[Fluid contacts|hydrocarbon contact]] at any depth. |
==Finite seal capacity of faults== | ==Finite seal capacity of faults== | ||
| − | Sealing faults may have some finite seal capacity. A fault may be able to support the pressure exerted by a 50-m hydrocarbon column but leak if the column increases to [[length::51 m]].<ref name=ch10r13>Chong, K. | + | Sealing faults may have some finite seal capacity. A fault may be able to support the pressure exerted by a 50-m hydrocarbon column but leak if the column increases to [[length::51 m]].<ref name=ch10r13>Chong, K. P., P. M. Hoyt, J. W. Smith, and B. Y. Paulsen, 1980, Effects of strain rate on oil shale fracturing: International Journal of Rock Mechanics, vol. 17, no. 1, p. 35–43., 10., 1016/0148-9062(80)90004-2</ref> Recent work suggests there may be a maximum seal capacity related to the percentage of shale in the fault gouge.<ref name=ch10r97>Yielding, G., B. Freeman, and D. T. Needham, 1997, [http://archives.datapages.com/data/bulletns/1997/06jun/0897/0897.htm Quantitative fault seal prediction]: AAPG Bulletin, vol. 81, no. 6, p. 897–917.</ref><ref name=ch10r74>Skerlec, G. M., 1997, Atlas of fault seal behavior in the Gulf Coast: Franklin, Pennsylvania, SEALS International, 4356 p.</ref> In most cases, however, the percent fill is significantly less and is limited by fault-dependent leak points rather than the seal capacity of the gouge. |
==See also== | ==See also== | ||
| Line 50: | Line 50: | ||
[[Category:Predicting the occurrence of oil and gas traps]] | [[Category:Predicting the occurrence of oil and gas traps]] | ||
[[Category:Evaluating top and fault seal]] | [[Category:Evaluating top and fault seal]] | ||
| + | [[Category:Treatise Handbook 3]] | ||
Latest revision as of 21:50, 28 March 2022
The percent fill of a trap is the percentage of the trap volume filled with hydrocarbons compared with its total volume. Percent fill can be controlled by a number of factors, including the following:
Control summary
Figure 1 summarizes the various controls on percent fill and hydrocarbon column height. The maximum fill case is the synclinal spill point (SSP). A cross-leaking fault limits the percent fill to the juxtaposed lithology leak point (JLLP). A dip-leaking fault limits the percent fill to the fault plane leak point (FPLP).
A cross-sealing fault allows fill below the JLLP and possibly as deep as the SSP. A trap also may be partially filled (PF) due to either charge or top seal capacity. A partially filled trap can have a hydrocarbon contact at any depth.
Finite seal capacity of faults
Sealing faults may have some finite seal capacity. A fault may be able to support the pressure exerted by a 50-m hydrocarbon column but leak if the column increases to length::51 m.[1] Recent work suggests there may be a maximum seal capacity related to the percentage of shale in the fault gouge.[2][3] In most cases, however, the percent fill is significantly less and is limited by fault-dependent leak points rather than the seal capacity of the gouge.
See also
References
- ↑ Chong, K. P., P. M. Hoyt, J. W. Smith, and B. Y. Paulsen, 1980, Effects of strain rate on oil shale fracturing: International Journal of Rock Mechanics, vol. 17, no. 1, p. 35–43., 10., 1016/0148-9062(80)90004-2
- ↑ Yielding, G., B. Freeman, and D. T. Needham, 1997, Quantitative fault seal prediction: AAPG Bulletin, vol. 81, no. 6, p. 897–917.
- ↑ Skerlec, G. M., 1997, Atlas of fault seal behavior in the Gulf Coast: Franklin, Pennsylvania, SEALS International, 4356 p.
External links
| find literature about Percent fill: controlling factors |
|
|
|
|