Sandstone permeability estimation from cuttings

From AAPG Wiki
Revision as of 17:19, 6 April 2022 by Cwhitehurst (talk | contribs) (added Category:Treatise Handbook 3 using HotCat)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
Exploring for Oil and Gas Traps
Series Treatise in Petroleum Geology
Part Predicting the occurrence of oil and gas traps
Chapter Predicting reservoir system quality and performance
Author Dan J. Hartmann, Edward A. Beaumont
Link Web page
Store AAPG Store

Sneider and King[1] developed a cuttings-based method of permeability estimation. Where cuttings are available, permeability estimates can be made by examining the surfaces of cuttings for petrophysical permeability indicators. Estimates of the permeability for a particular formation can be extended into areas without data in order to predict permeability.

Basis

Sneider and others at Shell Oil Company developed a methodology for estimating permeability from cuttings by calibrating permeability measured from cores with rock-pore parameters described in cuttings. Cores of known permeability were ground up until chips from the core were the size of cuttings. By using comparators made from core chips, they estimated formation permeability from cuttings with surprising accuracy. Although Sneider and King[1] describe the method for estimating sandstone permeability from cuttings (presented below), procedures could just as easily be developed to predict permeability of carbonates from cuttings.

Petrophysical description

From examination of cuttings, sandstone permeability can be predicted using the following petrophysical descriptions:

  • Grain size and sorting
  • Degree of rock consolidation
  • Volume percent of clays
  • Pore sizes and pore interconnections
  • Size and distribution of pore throats

Sneider's pore classification for clastics

Sneider and King[1] developed a simple method of classifying pore types from cuttings. The classification of clastic rock pore types from cuttings is made by comparing pore types with production tests and log analysis. The pore types are as follows:

Type Description
I Rocks with pores capable of producing gas without natural or artificial fracturing.
II Rocks with pores capable of producing gas with natural or artificial fracturing and/or interbedded with type I rocks.
III Rocks too tight to produce at commercial rates even with natural or artificial fracturing.

The table below lists the characteristics of pore types I, II, and III.

Pore type Characteristics of dry, freshly broken surfaces at 20× magnification Permeability
Visible Pinpoint Consolidation
I Abundant to common; interconnection visible on many pores Very abundant to common Needle probe easily dislodges many grains from rock surface Type I Subclasses
IA:>100md
IB: 10–100 md
IC: 1–10 md
ID: ±0.5–1 md
II Scattered Abundant to common Needle probe can only occasionally dislodge a grain from rock surface ± 0.5–1.0 md (depending on particle size, sorting, and clay mineral content)
III None to very isolated None to a few pores Usually very well consolidated and/or pores filled with clays or other pore-filling material Too tight to produce gas at commercial rates even when fractured or interbedded with type I rocks

Examples of pore type I

Figure 1 Examples of rocks with types IA, IB, IC, and ID. From Sneider and King;[1] courtesy AAPG.

The SEM microphotographs in Figure 1 are examples of rocks with types IA, IB, IC, and ID.

Note the amount and connectivity of pore space of each subclass.

Pore types II and III

Figure 2 Examples of rocks with types II and III. From Sneider and King;[1] courtesy AAPG.

The SEM microphotographs in Figure 2 are examples of rocks with types II and III. Note the amount and connectivity of pore space of each subclass.

Procedure: predicting sandstone permeability

The procedure below is for predicting the permeability of sandstones from cuttings using 20× magnification[1].

  1. Estimate grain size and sorting using standard size-sorting comparators, thin section and SEM photomicrographs, and rock photographs.
  2. Estimate volume percentages using Terry-Chillingar charts made for volume estimates.
  3. Estimate consolidation using the scheme described in the preceding table.
  4. Describe the visible and pinpoint porosity and interconnectedness.
  5. Estimate permeability from rocks on comparators and/or using rock characteristics described in the preceding table. (Comparators can be made or purchased.)
  6. Predict permeability for the formation in prospective areas where petrophysical characteristics are believed to be similar

See also

References

  1. 1.0 1.1 1.2 1.3 1.4 1.5 Sneider, R., M., King, H., R., 1984, Integrated rock-log calibration in the Elmworth field—Alberta, Canada: part I: reservoir rock detection and characterization, in Masters, J., A., ed., Elmworth—Case Study of a Deep Basin Gas Field: AAPG Memoir 38, p. 205–214.

External links

find literature about
Sandstone permeability estimation from cuttings
Datapages button.png GeoScienceWorld button.png OnePetro button.png Google button.png