Relative permeability

From AAPG Wiki
Jump to navigation Jump to search

Absolute, effective, and relative permeability

Reservoirs contain water and oil or gas in varying amounts. Each interferes with and impedes the flow of the others. The aquifer portion of a reservoir system by definition contains water as a single phase (100% Sw). The permeability of that rock to water is absolute permeability (Kab). The permeability of a reservoir rock to any one fluid in the presence of others is its effective permeability to that fluid. It depends on the values of fluid saturations. Relative permeability to oil (Kro), gas (Krg), or water (Krw) is the ratio of effective permeability of oil, gas, or water to absolute permeability. Relative permeability can be expressed as a number between 0 and 1.0 or as a percent. Pore type and formation wettability affect relative permeability.

Why kro or krg is less than kab

 
Figure 1 See text for explanation.

A pore system saturated 100% with any fluid transmits that fluid at a rate relative to the pore throat size and the pressure differential. In the drawing in Figure 1, the absolute pore throat size (A) is noted as the distance between grain surfaces. When a sample contains oil or gas and water (where water wets the grain surface), the pore throat size (B) for oil or gas flow is less than the absolute pore throat size (A). The thickness of the water layer coating the grains is proportional to the Sw of the rock. In other words, as buoyancy pressure increases, Sw decreases and the effective size of the pore throat for oil or gas flow (B) increases.

Interpreting a relative permeability curve

The diagram below shows relationships between relative permeability curves (drainage and imbibition), capillary pressure, and fluid distribution in a homogeneous section of a reservoir system. The reservoir system rock has a porosity of 30% and a permeability of 10 md (r35 = 1.1μ). Laboratory single-phase air permeability is typically used to represent absolute permeability (Ka when determining relative permeability to oil or water at a specific Sw.

The figure below depicts three relative permeability curves:

  • Water (Krw)—similar for both drainage and imbibition tests
  • Oil drainage (Kro-D)—reflects migrating oil displacing water (decreasing Sw) with increasing buoyancy pressure (Pb)
  • Oil imbibition (Kro-I)—reflects reduction in oil saturation (S0) as a water front moves through a rock sample, resaturating it with water (Sxo)

The curve labeled Kro represents the relative permeability of a formation to oil in the presence of varying water saturation (Sw). The curve labeled Krw represents the relative permeability of the formation to water.

Consider points A–D below. Point A, at Sw = 100%, is the original condition of the sample. Here Krw ≈ Ka (10 md). At point B (Sw ≈ 90%, S0 = 10%), oil breaks through the sample, representing the migration saturation of the sample; Kro = 1.0. At point C (Sw ≈ 50%, So ≈ 10%), Krw is less than 1% of Ka and water, now confined to only the smallest ports, ceases to flow while oil flow approaches its maximum. At point D on the Kro-D curve (Sw ≈ 20%, So ≈ 80%), relative permeability is approaching 1.0 (~ 10 md).

Figure 9-27 is an example of “drainage” relative permeability of a water-wet reservoir. It shows changes in Kro and Krw as Sw decreases, as in a water-drive reservoir during hydrocarbon fill-up. “Imbibition” Kro and Krw have a different aspect, being measured while Sw increases, as it does during production in a reservoir with a water drive.

 
Figure 9-27 Modified.

Drainage vs. imbibition curves

The drainage curve determines from computed Sw whether a zone is representative of lower transitional (Krw> Kro - D), upper transitional (Krwro - D), or free oil (Krw ≈ 0). The imbibition curve relates to performance due to filtrate invasion from water injection or flushing from natural water drive.

Pore throat size and kr

Every pore type has a unique relative permeability signature. Consider the hypothetical drainage relative permeability type curves shown below. Curves A, B, and C represent the relative permeability relationships for rocks with different port types: macro, meso, and micro, respectively. Curve A represents a rock with greater performance capability than B or C. Note how critical water saturation decreases as pore throat size increases. Also note the changing position of Kro–Krw crossover with changes in pore throat size.

Critical water saturation

Critical Sw is the point where water saturation is so low that no significant water cut can be measured; only hydrocarbon flows from the reservoir. At Sw higher than critical Sw, water flows with hydrocarbon. Where Sw becomes great enough, only water flows.

Critical water saturation

The critical Sw value is different for each port type. Curve A in Figure 9-28 represents rocks with macroporosity. It has a critical Sw less than 20%. Curve B represents a rock (continued) with mesoporosity. Mesoporous rocks have a critical Sw of 20–60%. Curve C represents rocks with microporosity. They have a critical Sw of 60–80%.

 
Figure 9-28 See text for explanation.

The table below summarizes representative critical Sw values for macro-, meso-, and micropore types that correspond to A, B, and C, respectively, in Figure 9-28.

Pore type Micro Meso Macro
Critical Sw 60–80% 20–60%
Length of transition zone >30 m 2–30 m 0–2 m

See also

External links

find literature about
Relative permeability